About
Community
Bad Ideas
Guns & Weapons
Irresponsible Activities
KA-FUCKING-BOOM!
Locks and Security
Scams and Rip-offs
Drugs
Ego
Erotica
Fringe
Society
Technology
register | bbs | search | rss | faq | about
meet up | add to del.icio.us | digg it

The Definitive Vending Machine File

by Fixit


NOTICE: TO ALL CONCERNED Certain text files and messages contained on this site deal with activities and devices which would be in violation of various Federal, State, and local laws if actually carried out or constructed. The webmasters of this site do not advocate the breaking of any law. Our text files and message bases are for informational purposes only. We recommend that you contact your local law enforcement officials before undertaking any project based upon any information obtained from this or any other web site. We do not guarantee that any of the information contained on this system is correct, workable, or factual. We are not responsible for, nor do we assume any liability for, damages resulting from the use of any information on this site.

Alright, I'm sick of reading all this crap on how to try and rip off vending machines when none of it works. Clay? Salt water? Gimme a fucking break. Keep reading to hear how to get into vending machines from someone who has worked with them for the last ten years, and still does.

Some warnings.

1- With electronics being so cheap these days, most people videotape their vending locations. Scope out the place first, look for cameras. At any rate, it's not good to look like you when you go raid the machines.

2- Almost all vending machines now have alarms and tilt switches installed on them. Candy machines have shock sensors on the front glass. All machines have plumb bobs on them. If at all possible, unplug the machine first to avoid tripping the anti-vandalism measures.

3- There was another warning I had all thought up, but now I can't remember it. I'll think of it later.

Okay, standard vending machines include soda machines, candy machines, cigarette machines and other upright product dispensing devices. I'll write a separate file for video games, bill changers and payphones later.

There are basically only two ways to get into vending machines without a key. Through the lock, or directly.

LOCKS

You can always try and pick the lock, using the standard method. The only problem with that is that there are usually at least eight settings, so you have to pick it three or four times to get the cylinder to travel enough to open the lock. That can be entirely too time consuming and generally not worth it. So, here are some better methods for opening a lock without picking it. It can be very easy to get into tubular locks or very hard, depending on how cheap the lock is.

Gematic-type: cheap as hell locks. Their main weakness is that the cam (small piece of metal on the back of the lock designed to hold the cylinder in place) is held on by a single, small, weak-threaded screw. Most of the time the cam is also only an aluminum alloy. To defeat this type of lock, you can use a tubular key. File it down so that only the pin that sticks up from the cylinder is left and when inserted into a lock it rotates freely, but you can't pull it out. Attach a chain to the key, then wrap the chain around a bar of some sort. Yank hard. Voila! Cam either comes completely off or is bent to hell, open sesame.

Ace-type: somewhat more expensive, better secure. The cam is held on by a nut over a larger bolt-type end. This makes it mainly pull-proof. However, the lock is only coated in carbon steel. Beneath that millimeter thin layer of hard metal there is only a nickel alloy. Insert a small drill bit into the cross section where the key slot meets the circular opening and go at it. After you get past the hard metal, the rest will give like soft cheese. Keep drilling until either the cylinder falls out, or you drill right through the lock and through the bolt in the end of the lock. It only takes me about five minutes to do this with a hammer drill.

American-type: you can tell these locks from the others by the fact that the face is completely flush. Instead of a tubular cylinder, these locks rely on a set of pins on the key, mounted at irregular depths. The face is drill-proof. These things are the Fort Knox of locks, if you see one you're pretty much fucked trying to open it without a key. So, on to the next method!

DIRECT

Let's not kid ourselves here. We're not trying to get into these things for the aesthetic value of the job. We want the stuff inside. C'mon, you want to try to dump salt water into these things, thinking it will completely ruin the machine and only work part of the time? I'm guessing we're not all that concerned with the well-being of the machine in question. Face it, this is a grab-and-go job. So fuck the lock, let's just get in.

Almost every single vending machine has the T-bar locking system. This means there's a steel bar traveling the length of the machine, securing the door at the top, bottom and side directly next to the lock, opposite the hinge.

This is a pretty good system. It doesn't work against someone determined to get in. Why? Because the point where the locking bar intersects with the machine's walls may be steel, but it's only about a quarter inch thick.

Bring a prybar and a hammer. Unplug the machine. Climb on top of it. Track where the locking bar intersects with the roof by going in a line straight up from the lock. Insert the prybar (you might have to hammer it down in) about an inch to the side of that position, toward the hinge. Pry the sucker open. Once you've got the top open, you can see where the locking bar goes into the side, pry that open too. From there you can yank the door open and grab anything you want.

A successful break-in to a vending machine should take less than three minutes. Doing it this way also doesn't damage the machine enough to make it unusable. In fact, it takes less than five minutes of welding to fix, thus the vending company loses very little... some product and a couple hundred dollars is chump change compared to the $7000 it costs for the machine. If you don't trash the machine, there's less of a chance the company will follow up on busting you for breaking into it.

2001

 
To the best of our knowledge, the text on this page may be freely reproduced and distributed.
If you have any questions about this, please check out our Copyright Policy.

 

totse.com certificate signatures
 
 
About | Advertise | Bad Ideas | Community | Contact Us | Copyright Policy | Drugs | Ego | Erotica
FAQ | Fringe | Link to totse.com | Search | Society | Submissions | Technology
Hot Topics
Robbing a dealer out of state (hypothetical)
Want Revenge on Some Guy's Car
Found CHeck
Breaking into garages?
House Arrest
Free Logitech Products Wihtout Owning
Urban Exploration
graffiti on google earth.
 
Sponsored Links
 
Ads presented by the
AdBrite Ad Network

 

TSHIRT HELL T-SHIRTS